CMM 500 Compressor Master Meter

The CS Instruments CMM 500 Compressor Master Meter is a high-precision reference flow meter engineered to measure the performance and Free Air Delivery (FAD) of compressors. Operating on the Venturi differential pressure principle according to ISO 5167, it delivers highly accurate readings (±0.5% accuracy) even in wet, saturated compressed air directly downstream of the compressor without requiring long straight pipe runs. The CMM 500 can be used both directly downstream of the compressor for measuring wet compressed air and as a compressed air meter for consumption measurement and billing of dry compressed air.

Description

Description

CS Instruments CMM 500 Compressor Master Meter – High-Precision Flow Measurement

The CS Instruments CMM 500 Compressor Master Meter is a high-precision reference flow meter designed to measure compressor capacity and compressed air consumption. It is suitable for measuring wet compressed air directly downstream of a compressor and dry compressed air in distribution systems.

Using a differential-pressure Venturi measurement principle, the CMM 500 delivers fast, accurate flow measurement across a wide operating range. Moreover, its low pressure loss and broad measuring span make it suitable for compressor performance testing, energy audits, and compressed air consumption monitoring.

With accuracy better than ±0.5% of measured value over the specified operating range, the CMM 500 supports reliable compressor capacity evaluation and applications requiring precise compressed air measurement.

Key Specifications

  • Manufacturer: CS Instruments
  • Model: CMM 500
  • Instrument type: Compressor master meter / reference flow meter
  • Measurement principle: Differential pressure using a Venturi measuring section
  • Measuring medium: Air and compatible gases
  • Measuring span: Greater than 1:130
  • Accuracy: ±0.5% of measured value from 20% to 100% of maximum flow; lower-range accuracy depends on configuration
  • Response time: Less than 1 second (t99)
  • Medium temperature: −20°C to +100°C
  • Operating pressure: Up to 16 bar(g); 30 bar(g) and 100 bar(g) versions available on request
  • Pressure loss: Less than 70 mbar at maximum flow
  • Power supply: 18–36 VDC
  • Standard outputs: 4–20 mA, pulse, and RS-485 Modbus-RTU
  • Optional interfaces: Modbus-TCP Ethernet, Power over Ethernet (PoE), and M-Bus
  • Process connection: DIN EN 1092-1 or ANSI flanges
  • Nominal sizes: DN 50, DN 80, DN 100, with DN 125, DN 150, and DN 200 available on request

Exact performance depends on the selected size, measuring section, gas properties, and installation conditions.

Working Principle

The CMM 500 uses the Venturi differential-pressure principle to determine gas flow.

  1. Gas enters the measuring section: Compressed air passes through the specially designed Venturi measuring section.
  2. Pressure difference develops: The geometry creates a pressure difference related to the gas velocity.
  3. Differential pressure is measured: The instrument measures the pressure difference across the measuring section.
  4. Flow is calculated: The electronics calculate flow using the differential pressure, calibrated measuring geometry, and configured gas properties.
  5. Operating conditions are considered: Pressure and temperature measurements support the calculation and display of standardised gas volume.
  6. Data is transmitted: Flow rate, total consumption, and other supported measurements are provided through the selected outputs or communication interfaces.

The CMM 500 can display standardised volume values such as Nm³ and Nm³/h. The reference conditions depend on the configured standard, such as DIN 1343 or ISO 1217 for compressed air.

Main Advantages

  • High measurement accuracy: Supports precise compressor capacity measurement and compressed air consumption monitoring.
  • Wide measuring range: A span greater than 1:130 accommodates substantial changes in demand.
  • Fast response: A response time below one second helps capture short-term flow changes.
  • Low pressure loss: Pressure loss remains below 70 mbar at maximum flow according to the manufacturer.
  • Wet compressed air capability: Suitable for measurement directly downstream of a compressor under specified operating conditions.
  • Dry compressed air monitoring: Can also be used for consumption measurement and billing applications.
  • Flexible gas measurement: Supports compatible gases when the correct gas properties are configured.
  • Multiple interfaces: Analogue, pulse, and digital communication options support integration into industrial monitoring systems.
  • Serviceable design: The mounting plate allows maintenance activities such as zero-point correction, condensate drainage, and sensor replacement under the manufacturer’s specified procedures.

Typical Applications

The CMM 500 is suitable for:

  • Compressor capacity and performance testing
  • Free-air-delivery (FAD) assessment
  • Compressed air energy audits
  • Compressed air consumption monitoring
  • Compressed air billing and submetering
  • Industrial gas flow measurement
  • Compressor comparison and efficiency evaluation
  • Flow reference measurements in compressed air systems

Installation Considerations

Install the CMM 500 in a suitable horizontal pipe run or riser, following the manufacturer’s installation instructions. The selected measuring section and flange configuration must match the pipeline.

For high accuracy, use the recommended inlet and outlet measuring sections to establish stable flow conditions. Severe disturbances caused by valves, check valves, partially closed ball valves, or abrupt changes in pipe geometry may require additional flow conditioning.

Before selecting the meter, confirm the nominal pipe size, operating pressure, gas composition, temperature, required flow range, and desired output interfaces.

CMM 500 for Compressor Capacity Measurement

The CMM 500 is designed to provide a reliable reference for evaluating compressor output. By measuring flow directly at the compressor discharge, users can assess delivered compressed air volume and compare performance against expected capacity.

When combined with pressure, temperature, and electrical power measurements, the flow data can also support a broader compressor efficiency assessment. This helps identify underperforming compressors, compare operating conditions, and find opportunities to reduce energy costs.

Conclusion

The CS Instruments CMM 500 Compressor Master Meter is a high-precision flow measurement solution for compressor capacity testing and compressed air consumption monitoring. Its Venturi differential-pressure principle, wide measuring span, fast response, and low pressure loss make it suitable for demanding industrial applications.

For facilities that need dependable compressor performance data or accurate compressed air consumption measurements, the CMM 500 provides a versatile reference flow meter.

About CS Instruments

CS Instruments, from Germany, makes measuring instruments for compressed air and gases, and Schmierer SEA offers nine of them from Shah Alam: flow meters for consumption and compressor capacity, the LD500 and LD510 ultrasonic leak detectors with camera, and dew point, particle and oil vapour sensors for air quality. Our team helps you select the instrument and set it up.

Which CS Instruments product for which job

JobProductStated figures
Consumption in dry airVA 500, 520, 550, 570Thermal mass flow, no moving parts; up to 40 bar (selected VA 520) or 50 bar (selected VA 550)
Wet air at the compressor outletVD 500-30 to +180 °C, up to 30 bar, DN 20 to DN 600
Compressor capacity and billingCMM 500±0.5% of reading from 20 to 100% of maximum flow
Flow without cutting the pipeVC600Clamp-on ultrasonic, pipes 25 to 90 mm outside diameter
Finding leaksLD500 and LD510Leak rate and annual cost estimate per leak; LD510 adds a sensor input
Dew point and humidityFA 510, FL 510Pressure dew point after the dryer; 0 to 100% RH
ParticlesPC400From 0.1 µm or 0.3 µm, three size channels
Oil vapourOil Check5000.001 to 5 mg/m³ at 3 to 9 bar
Air quality as one systemCompressed Air Quality MonitoringParticle, moisture and oil sensors on one interface

Where to start

  • High energy bill: measure consumption with a VA sensor, then find the leaks with the LD500.
  • Compressor performance in doubt: the CMM 500 is built as a reference meter for free air delivery.
  • Air quality requirements: ISO 8573-1 classes air by particles, water and oil; the PC400, FA 510 and Oil Check500 measure each.

All CS Instruments products and the compact gas flow sensors we offer are on the compressed air flow meter page. Tell us the pipe size, pressure and what you need to know, and send an enquiry.