A compressed air flow meter shows what each compressor delivers and what each line uses; flow that carries on when production stops points to leaks. Schmierer SEA offers compressed air instruments from our partner CS Instruments: thermal mass, wet-air and clamp-on flow meters, the LD500 and LD510 ultrasonic leak detectors with camera, and dew point, particle and oil vapour monitors.

Which instrument for which job

Nine CS Instruments products and two compact Müller IE sensors; the figures are the ones each product page states, so you can see which compressed air flow meter or monitor fits the task.

Job Product How it measures Stated figures
Consumption in dry air VA 500, 520, 550, 570 Thermal mass flow, no moving parts Up to 40 bar (selected VA 520) or 50 bar (selected VA 550)
Wet air at the compressor outlet VD 500 Differential pressure -30 to +180 °C, up to 30 bar, DN 20 to DN 600, typically ±1.5% of reading
Compressor capacity (FAD), billing CMM 500 Venturi differential pressure ±0.5% of reading from 20 to 100% of maximum flow; span over 1:130; under 70 mbar loss
Flow without cutting the pipe VC600 Clamp-on ultrasonic Pipes 25 to 90 mm outside diameter, from 3 bar(g), up to 25 m/s
Finding leaks LD500 and LD510 Ultrasound, with camera Leak rate in L/min or CFM and annual cost estimate; LD510 adds a sensor input
Dew point and humidity FA 510, FL 510, IAC 500, IAC 510 Dew point, humidity and ambient sensors FA 510: pressure dew point after the dryer, IP66; FL 510: 0 to 100% RH; IAC 500/510: ambient conditions around the compressor
Particles PC400 Optical laser counter From 0.1 µm or 0.3 µm, three size channels
Oil vapour Oil Check500 Photoionisation detector 0.001 to 5 mg/m³ at 3 to 9 bar
Air quality as one system Compressed Air Quality Monitoring Particle, moisture and oil sensors on one interface See product page
Gas flow in machines and ducts MEFS-K, MKFS Calorimetric MEFS-K: 2 to 2000 cm/s, G1/4 or G1/2; MKFS: gases 2 to 2000 cm/s, G1/4 or G1/2

How to choose a compressed air flow meter

  • Before or after the dryer: hot, wet air at the compressor outlet needs the VD 500 or CMM 500; dry air in the distribution suits the VA series.
  • No shutdown: the VC600 clamps onto the outside of the pipe, and the VD 500 can be fitted under pressure through a 1/2 in ball valve; the VA 550 also installs through a ball valve where its configuration permits.
  • Capacity tests and billing: the CMM 500 is built as a reference meter for free air delivery and for metering dry air.
  • Leak surveys: the LD500 locates and photographs each leak and estimates its rate and annual cost; choose the LD510 to read dew point, flow, pressure or temperature with the same instrument.
  • Air quality: ISO 8573-1 classes air by particles, water and oil, so pair the PC400, FA 510 and Oil Check500 to monitor all three (the Oil Check500 covers oil vapour).
  • Hazardous areas and other gases: VA 550 and VA 570 versions with ATEX/IECEx or DVGW approval are available, depending on version.

Tell us the pipe size, pressure and what you need to know (consumption, capacity, quality or leaks), and our team in Shah Alam will help you select the instrument and set it up: send an enquiry. See also thermal gas flow meters and ultrasonic flow meters.

To plan the measuring points for a whole plant, read how to implement a compressed air monitoring system.

Showing all 11 results

CMM 500 Compressor Master Meter

In stock

SKU: CMM500
The CS Instruments CMM 500 Compressor Master Meter is a high-precision reference flow meter engineered to measure the performance and Free Air Delivery (FAD) of compressors. Operating on the Venturi differential pressure principle according to ISO 5167, it delivers highly accurate readings (±0.5% accuracy) even in wet, saturated compressed air directly downstream of the compressor without requiring long straight pipe runs. The CMM 500 can be used both directly downstream of the compressor for measuring wet compressed air and as a compressed air meter for consumption measurement and billing of dry compressed air.

Compressed Air Humidity Monitoring

In stock

SKU: FA510, FL510, IAC500, IAC510
CS Instruments offers a range of sensors for monitoring moisture, humidity, and environmental conditions in compressed air systems. These instruments help operators maintain air quality, protect equipment, and improve process reliability. Moisture monitoring is particularly important in compressed air installations. Excess moisture can cause corrosion, damage pneumatic equipment, contaminate products, and affect sensitive manufacturing processes. Therefore, selecting the correct measurement technology is essential. The FA 510, FL 510, IAC 500, and IAC 510 provide different measurement functions for compressed air systems, industrial gases, compressor intake air, and controlled environments.

Compressed Air Quality Monitoring

In stock

SKU: compressed air quality monitoring
CS Instruments Compressed Air Quality Monitoring Solutions represent a comprehensive ecosystem of stationary and mobile instrumentation engineered to analyze, track, and validate compliance with strict ISO 8573-1 purity classifications. By combining multi-sensor networks into singular diagnostic interfaces, these systems provide real-time tracking for the three critical industrial contaminants: solid aerosol particles, moisture vapor, and vaporous residual oil.

LD500 & LD510 Ultrasonic Leak Detector with Camera

In stock

SKU: LD500, LD510
The CS Instruments LD 500 and LD 510 Ultrasonic Leak Detectors help users locate, quantify, and document compressed air and gas leaks. These portable instruments use ultrasonic detection technology to identify escaping gas, even when the leakage point is difficult to access or the surrounding production environment is noisy. Moreover, the integrated camera and touchscreen allow technicians to photograph leaks, record their locations, and document the required repair work directly on site. The instruments can also estimate leakage rates and potential annual energy-cost savings, helping businesses reduce compressed air losses and improve energy efficiency. The LD 500 is designed for ultrasonic leak detection and documentation. In comparison, the LD 510 adds a configurable sensor input for compatible CS Instruments sensors, extending its use to measurements such as dew point, flow, pressure, and temperature.

MEFS-K Compact Gas Flow Sensor

In stock

SKU: MEFS-K
Achieve absolute precision and rapid response tracking inside your industrial gas distribution loops and exhaust ventilation mains. For this reason, plant utility operators, machinery builders, and automation engineers deploy the Müller Industrie-Elektronik MEFS-K series. They do this specifically to secure continuous, real-time gas velocity diagnostics. Because this high-performance electronic sensor utilizes advanced calorimetric or thermal dispersion measurement principles, it completely eliminates pressure drops, spinning parts, and mechanical wear common to traditional turbine meters. Furthermore, it easily operates independently of line pressure and ambient temperature shifts. Consequently, your processing line achieves continuous velocity monitoring. As a result, it ensures immediate leakage detection, provides reliable compressor protection loops, and guarantees absolute point safety under demanding layout constraints.

MKFS Compact Calorimetric Flow Sensor

In stock

SKU: MKFS
The MKFS series from Müller Industrie-Elektronik is a modular, highly compact calorimetric flow sensor explicitly built for measuring the flow velocity of air and other non-corrosive gases up to 25 m/s. Constructed with a robust stainless steel thermowell and housing, it features versatile output variants including 4...20 mA, 0...20 mA, and 0...10 V, alongside optional RS232 digital interfaces. Its small footprint and high reliability make it excellent for climate control, ventilation, and fire extinguishing plants.

Oil Check500 Oil Vapor in Compressed Air

In stock

SKU: Oilcheck500
The CS Instruments OIL CHECK 500 is an advanced online monitoring system designed for high-precision, continuous measurement of vaporous residual oil content in compressed air, nitrogen and other gases like nitrogen, ensuring direct compliance with ISO 8573 standards: stationary and mobile version, compact design Unique sensitivity for compressed air of the recommended oil vapour standard according to ISO 8573-5 Auto calibration through "Forced Pressure Variation"

PC400 Particle Counter in Compressed Air

In stock

SKU: Particle Counter PC 400
The CS Instruments PC 400 Particle Counter is a high-precision optical instrument designed to measure solid particle contamination in compressed air and industrial gases. It detects particles as small as 0.1 µm, helping users assess compressed air purity and monitor filtration performance. Moreover, the PC 400 supports compressed air quality assessment according to ISO 8573-1. It helps identify filter breakthrough and unexpected particle contamination before these issues affect sensitive equipment or production processes. Available in stationary and portable configurations, the PC 400 is suitable for continuous monitoring, maintenance inspections, and compressed air quality audits.

Thermal Mass Flow VA series

In stock

SKU: VA series
The CS Instruments VA  are highly accurate, cost-effective thermal mass flow meters designed specifically for monitoring of compressed air, and gases for inline, insertion and flange type installation: direct mass flow measurement, no wear, low loss. VA 500 / VA 520: Compact inline or insertion meters built for standard compressed air, nitrogen, oxygen, argon, and CO2 monitoring. VA 550 / VA 570: Heavy-duty and robust industrial versions with stainless steel wetted parts, optional ATEX/IECEx or DVGW approvals for flammable or harsh gases like natural gas, hydrogen, and biogas.

VC600 Clamp-on Ultrasonic Gas Flow Sensor

In stock

SKU: VC600
Optimize your gas monitoring and energy auditing without cutting a single pipe with the CS Instruments VC 600. Expertly manufactured by CS Instruments, this high-performance non-invasive clamp-on flow sensor tracks compressed air and industrial gases from the outside. Furthermore, its ultra-safe clamp architecture eliminates installation downtime, contamination threats, and costly pressure drops across your entire production plant. Watch Video PDF Datasheet

VD500 Flow Sensor for Wet Compressed Air

In stock

SKU: VD500
The CS Instruments VD 500 Flow Sensor measures compressed air flow directly downstream of the compressor, where the air can still contain moisture and reach elevated temperatures. It is designed to measure flow, total consumption, temperature, and pressure, making it particularly useful for compressor performance analysis and compressed air energy audits. Unlike thermal mass flow sensors intended for dry compressed air, the VD 500 uses a differential-pressure measurement principle. Its robust design supports high flow velocities and temperatures up to 180°C. In addition, the sensor can be installed through a ½-inch ball valve under pressure, reducing the need to shut down the system for installation when the correct fittings and safety procedures are used.