UFP-1.0 Portable Clamp-On Ultrasonic Flowmeter

The Schmierer SEA UFP-1.0 Portable Ultrasonic Flowmeter provides a convenient solution for checking liquid flow without cutting into or interrupting the pipeline. It uses clamp-on ultrasonic transducers to measure flow from outside the pipe. Therefore, technicians can perform flow checks without removing sections of pipe or installing an in-line meter.

The UFP-1.0 supports short-term measurements, long-term monitoring, data logging, and verification of existing flowmeters. Moreover, its portable design, rechargeable lithium-ion battery, and backlit color display make it suitable for field inspections and routine maintenance. With a stated pipe size range of DN25 to DN5000, it can support flow measurement across a wide variety of pipeline sizes.

SKU: SSEA UFP1.0 Categories: ,
Description

Description

Key Features

  • Non-invasive clamp-on measurement: The transducers mount on the outside of the pipe, allowing flow checks without direct contact with the process liquid.
  • Wide pipe size range: Supports pipe diameters from 25 mm to 5000 mm, subject to the appropriate installation configuration.
  • Portable design: The handheld transmitter and carrying case support transportation between measurement locations.
  • High-resolution display: The 4.3-inch TFT LCD with backlighting simplifies setup and measurement monitoring.
  • Data logging: A 2 GB SD card stores measurement data for later transfer and evaluation.
  • Rechargeable battery: The lithium-ion battery supports up to 12 hours of continuous operation under the manufacturer’s stated conditions.
  • Analog output: A 4–20 mA output supports integration with compatible monitoring or recording equipment.
  • Industrial enclosure: The transmitter features an IP65-rated die-cast aluminum enclosure.

Working Principle

The UFP-1.0 uses ultrasonic signals to measure the flow of liquid through a pipe. Its clamp-on transducers attach to the pipe’s exterior and transmit and receive ultrasonic signals through the pipe wall and liquid.

The instrument processes the received signals to determine the liquid’s flow velocity. It then uses the configured pipe dimensions and measurement parameters to calculate the flow rate. Because the transducers remain outside the pipeline, the installation avoids direct contact with the process liquid and does not require cutting the pipe.

For reliable measurements, technicians must select a suitable installation location and configure the instrument correctly. In addition, they should follow the manufacturer’s recommendations for transducer spacing, mounting method, and upstream and downstream straight-pipe requirements. The supplied brochure describes both V-method and Z-method transducer mounting arrangements.

Technical Specifications

  • Product name: UFP-1.0 Portable Ultrasonic Flowmeter
  • Measurement technology: Clamp-on ultrasonic flow measurement
  • Flow velocity range: 0.12 to 12 m/s, as stated in the brochure
  • Accuracy: ±1.0% within the specified velocity ranges of approximately 0.5 to 5 m/s (1.6 to 16 ft/s)
  • Repeatability: 0.15%
  • Pipe size range: DN25 to DN5000 (25 mm to 5000 mm; approximately 1 to 200 inches)
  • Display: 4.3-inch TFT LCD
  • Keyboard: 22 touch keys
  • Power supply: Rechargeable lithium-ion battery
  • Battery operating time: Up to 12 hours of continuous operation, according to the brochure
  • Transmitter enclosure: IP65-rated die-cast aluminum enclosure
  • Output: 4–20 mA
  • Transducer operating temperature: The brochure states -40°C to +120°C
  • Standard transducer cable length: 5 m (approximately 16 ft)
  • Data storage: 2 GB SD card
  • Transducer mounting methods: V method and Z method

Transducer Mounting Methods

  • V method: The brochure identifies this as the standard mounting method. It is generally used for pipe diameters of approximately 25 mm to 400 mm.
  • Z method: This method supports larger pipe diameters, approximately 100 mm to 5000 mm. The brochure recommends considering the Z method for pipe diameters above 300 mm.

However, the best mounting arrangement depends on the pipe size, installation conditions, and signal quality. Technicians should follow the manufacturer’s installation guidance to achieve reliable measurement results.

Applications

  • Water distribution systems: Check flow at different points in water supply networks.
  • Existing flowmeter verification: Compare readings from installed flowmeters with portable measurements.
  • Industrial process monitoring: Perform temporary flow checks on compatible liquid pipelines.
  • Maintenance and troubleshooting: Investigate flow conditions without modifying the pipeline.
  • Hydrology and engineering surveys: Collect flow data during field studies and engineering inspections.
  • Long-term monitoring: Record flow measurements for subsequent analysis using the SD card.

These applications reflect the manufacturer’s stated uses for flow checks, monitoring, data logging, and existing meter verification.

Benefits of the Schmierer SEA UFP-1.0

  • Reduced installation work: Clamp-on transducers measure from outside the pipe, avoiding the need to cut into the pipeline for sensor installation.
  • Flexible field measurements: The portable design allows technicians to check multiple measurement points.
  • Convenient data collection: The display, SD card, and 4–20 mA output support different measurement and recording workflows.
  • Extended field operation: The rechargeable battery supports up to 12 hours of continuous operation under the stated conditions.
  • Broad pipe compatibility: The specified pipe size range supports measurements on both small and large pipelines when the installation is suitable.
  • Useful for meter checks: Technicians can use portable readings to help assess the performance of existing flowmeters.
About SSEA

SSEA instruments are Schmierer SEA's own range, offered from Shah Alam and led by pressure gauges. The SRU 25 stainless steel pressure gauge uses a silicon-jelly stabiliser instead of liquid filling and is rated IP66. The STU02 bimetallic thermometer is built to EN 13190. Gauge accessories, flow meters, water quality sensors and calibration tools complete the range.

SSEA instruments by family

FamilySSEA productsStated figures
Pressure gaugesSRU 25, SRU 25X with mini diaphragm seal, SRU 35, SR 01; SRU25 chemical gauges in Hastelloy, Monel and Inconel; SRU15 and SR15 boiler gauges; PCU05 phenolic case gaugeSRU 25: -1 to 100 bar, special versions up to 1,600 bar; 1% fsd with the 100 mm dial
Test pressure gaugesSRU15 test gauge, SFU 15, SF 15250 mm dial
Gauge accessoriesSyphons, cooling tower, snubbers, overload protectors, gauge cocks, shut-off valve, 3-way, 3-valve and 5-valve manifolds, swivel adapter, max drag pointerSee product pages
Electrical pressurePTX-36 gauge transmitter, SSEA-PTIII transmitter, DTG200 digital gaugePTX-36: 4–20 mA, dial still reads in a power failure; DTG200: -1 to 2,500 bar
Pressure calibrationIDTG 100 pressure calibrator, HPCP-700 hydraulic comparison pumpIDTG 100: -1 to 600 bar
TemperatureSTU02 bimetallic and STU01 gas filled thermometers, STW bar-stock thermowellsSTU02 bimetal thermometer to EN 13190
Flow metersCMF VIII Coriolis, MFIII electromagnetic, VFIII vortex, SWFVI swirl, TMFIII thermal mass, OGMFIII oval gear, VAFIII variable area, WMIII, TFLIII and TFGIII turbine, UCOF and UFP-1.0 clamp-on ultrasonicSee product pages
Water qualityDigital sensors for pH, dissolved oxygen, conductivity, turbidity, suspended solids, COD, ammonia nitrogen, nitrate, free chlorine, oil in water, blue-green algae, transparency and colour; MPSX sonde, HMSX handheld meter, MPTX and DCCX controllersSee product pages

How to choose within the range

  • General industrial duty: the SRU 25, all stainless steel with an SS316L tube and socket.
  • Corrosive or viscous media: the SRU 25X with its mini diaphragm seal, or an SRU25 chemical gauge.
  • Pressure testing and reference readings: a 250 mm test gauge, or the DTG200 digital gauge.
  • A reading in the control room: the PTX-36 sends 4–20 mA and keeps its local dial.
  • Temperature on a dial: the STU02 bimetallic or STU01 gas filled thermometer, with an STW thermowell where the stem needs protection.

Service in Shah Alam

Common pressure and temperature gauges are kept in warehouse stock. Our trained technical staff calibrate pressure, temperature and flow instruments in-house and on site. Our diaphragm seal filling station, in Shah Alam since June 2016, assembles seals for gauges, switches and transmitters of any brand.

Send the medium, range and connection and we will match one of our SSEA instruments: send an enquiry. The full gauge line-up is on the pressure gauge page.