CS Instruments, from Germany, makes measuring instruments for compressed air and gases, and Schmierer SEA offers nine of them from Shah Alam: flow meters for consumption and compressor capacity, the LD500 and LD510 ultrasonic leak detectors with camera, and dew point, particle and oil vapour sensors for air quality. Our team helps you select the instrument and set it up.

Which CS Instruments product for which job

Job Product Stated figures
Consumption in dry air VA 500, 520, 550, 570 Thermal mass flow, no moving parts; up to 40 bar (selected VA 520) or 50 bar (selected VA 550)
Wet air at the compressor outlet VD 500 -30 to +180 °C, up to 30 bar, DN 20 to DN 600
Compressor capacity and billing CMM 500 ±0.5% of reading from 20 to 100% of maximum flow
Flow without cutting the pipe VC600 Clamp-on ultrasonic, pipes 25 to 90 mm outside diameter
Finding leaks LD500 and LD510 Leak rate and annual cost estimate per leak; LD510 adds a sensor input
Dew point and humidity FA 510, FL 510 Pressure dew point after the dryer; 0 to 100% RH
Particles PC400 From 0.1 µm or 0.3 µm, three size channels
Oil vapour Oil Check500 0.001 to 5 mg/m³ at 3 to 9 bar
Air quality as one system Compressed Air Quality Monitoring Particle, moisture and oil sensors on one interface

Where to start

  • High energy bill: measure consumption with a VA sensor, then find the leaks with the LD500.
  • Compressor performance in doubt: the CMM 500 is built as a reference meter for free air delivery.
  • Air quality requirements: ISO 8573-1 classes air by particles, water and oil; the PC400, FA 510 and Oil Check500 measure each.

All CS Instruments products and the compact gas flow sensors we offer are on the compressed air flow meter page. Tell us the pipe size, pressure and what you need to know, and send an enquiry.

Showing all 9 results

CMM 500 Compressor Master Meter

In stock

SKU: CMM500
The CS Instruments CMM 500 Compressor Master Meter is a high-precision reference flow meter engineered to measure the performance and Free Air Delivery (FAD) of compressors. Operating on the Venturi differential pressure principle according to ISO 5167, it delivers highly accurate readings (±0.5% accuracy) even in wet, saturated compressed air directly downstream of the compressor without requiring long straight pipe runs. The CMM 500 can be used both directly downstream of the compressor for measuring wet compressed air and as a compressed air meter for consumption measurement and billing of dry compressed air.

Compressed Air Humidity Monitoring

In stock

SKU: FA510, FL510, IAC500, IAC510
CS Instruments offers a range of sensors for monitoring moisture, humidity, and environmental conditions in compressed air systems. These instruments help operators maintain air quality, protect equipment, and improve process reliability. Moisture monitoring is particularly important in compressed air installations. Excess moisture can cause corrosion, damage pneumatic equipment, contaminate products, and affect sensitive manufacturing processes. Therefore, selecting the correct measurement technology is essential. The FA 510, FL 510, IAC 500, and IAC 510 provide different measurement functions for compressed air systems, industrial gases, compressor intake air, and controlled environments.

Compressed Air Quality Monitoring

In stock

SKU: compressed air quality monitoring
CS Instruments Compressed Air Quality Monitoring Solutions represent a comprehensive ecosystem of stationary and mobile instrumentation engineered to analyze, track, and validate compliance with strict ISO 8573-1 purity classifications. By combining multi-sensor networks into singular diagnostic interfaces, these systems provide real-time tracking for the three critical industrial contaminants: solid aerosol particles, moisture vapor, and vaporous residual oil.

LD500 & LD510 Ultrasonic Leak Detector with Camera

In stock

SKU: LD500, LD510
The CS Instruments LD 500 and LD 510 Ultrasonic Leak Detectors help users locate, quantify, and document compressed air and gas leaks. These portable instruments use ultrasonic detection technology to identify escaping gas, even when the leakage point is difficult to access or the surrounding production environment is noisy. Moreover, the integrated camera and touchscreen allow technicians to photograph leaks, record their locations, and document the required repair work directly on site. The instruments can also estimate leakage rates and potential annual energy-cost savings, helping businesses reduce compressed air losses and improve energy efficiency. The LD 500 is designed for ultrasonic leak detection and documentation. In comparison, the LD 510 adds a configurable sensor input for compatible CS Instruments sensors, extending its use to measurements such as dew point, flow, pressure, and temperature.

Oil Check500 Oil Vapor in Compressed Air

In stock

SKU: Oilcheck500
The CS Instruments OIL CHECK 500 is an advanced online monitoring system designed for high-precision, continuous measurement of vaporous residual oil content in compressed air, nitrogen and other gases like nitrogen, ensuring direct compliance with ISO 8573 standards: stationary and mobile version, compact design Unique sensitivity for compressed air of the recommended oil vapour standard according to ISO 8573-5 Auto calibration through "Forced Pressure Variation"

PC400 Particle Counter in Compressed Air

In stock

SKU: Particle Counter PC 400
The CS Instruments PC 400 Particle Counter is a high-precision optical instrument designed to measure solid particle contamination in compressed air and industrial gases. It detects particles as small as 0.1 µm, helping users assess compressed air purity and monitor filtration performance. Moreover, the PC 400 supports compressed air quality assessment according to ISO 8573-1. It helps identify filter breakthrough and unexpected particle contamination before these issues affect sensitive equipment or production processes. Available in stationary and portable configurations, the PC 400 is suitable for continuous monitoring, maintenance inspections, and compressed air quality audits.

Thermal Mass Flow VA series

In stock

SKU: VA series
The CS Instruments VA  are highly accurate, cost-effective thermal mass flow meters designed specifically for monitoring of compressed air, and gases for inline, insertion and flange type installation: direct mass flow measurement, no wear, low loss. VA 500 / VA 520: Compact inline or insertion meters built for standard compressed air, nitrogen, oxygen, argon, and CO2 monitoring. VA 550 / VA 570: Heavy-duty and robust industrial versions with stainless steel wetted parts, optional ATEX/IECEx or DVGW approvals for flammable or harsh gases like natural gas, hydrogen, and biogas.

VC600 Clamp-on Ultrasonic Gas Flow Sensor

In stock

SKU: VC600
Optimize your gas monitoring and energy auditing without cutting a single pipe with the CS Instruments VC 600. Expertly manufactured by CS Instruments, this high-performance non-invasive clamp-on flow sensor tracks compressed air and industrial gases from the outside. Furthermore, its ultra-safe clamp architecture eliminates installation downtime, contamination threats, and costly pressure drops across your entire production plant. Watch Video PDF Datasheet

VD500 Flow Sensor for Wet Compressed Air

In stock

SKU: VD500
The CS Instruments VD 500 Flow Sensor measures compressed air flow directly downstream of the compressor, where the air can still contain moisture and reach elevated temperatures. It is designed to measure flow, total consumption, temperature, and pressure, making it particularly useful for compressor performance analysis and compressed air energy audits. Unlike thermal mass flow sensors intended for dry compressed air, the VD 500 uses a differential-pressure measurement principle. Its robust design supports high flow velocities and temperatures up to 180°C. In addition, the sensor can be installed through a ½-inch ball valve under pressure, reducing the need to shut down the system for installation when the correct fittings and safety procedures are used.