OFST-ID optical level sensor

The Müller Industrie-Elektronik OFST-ID Optical Level Sensor provides accurate, non-contact liquid-level measurement using low-power laser technology. It measures the distance between the sensor and the liquid surface without requiring direct contact with the medium. Consequently, it is suitable for applications where reliable level monitoring, compact installation, and reduced sensor contact are important.

With a measuring range of up to 4,000 mm, an accuracy of ±3 mm, and an IP68 protection rating, the OFST-ID supports level monitoring in tanks and containers. Moreover, its Bluetooth interface simplifies configuration, including applications involving different tank geometries.

SKU: OFST-ID Categories: ,
Description

Description

Key Specifications

  • Manufacturer: Müller Industrie-Elektronik
  • Model: OFST-ID
  • Instrument type: Optical level sensor
  • Measurement principle: Low-power laser time-of-flight (ToF)
  • Measuring range: Up to 4,000 mm
  • Accuracy: ±3 mm
  • Sampling rate: 1 Hz
  • Output signal: 4–20 mA
  • Supply voltage: 8–33 VDC
  • Operating temperature: −20°C to +80°C
  • Configuration interface: Bluetooth
  • Housing material: Polycarbonate
  • Seal material: NBR
  • Protection rating: IP68
  • Dimensions: Approximately Ø66 × 31 mm
  • Tank geometry: Standard formats plus up to 20 configurable measuring points

Specifications are based on the manufacturer’s published product information and datasheet.

Working Principle

The OFST-ID uses the time-of-flight principle to determine the distance to the liquid surface.

  1. Laser emission: The sensor emits low-power laser light toward the liquid surface.
  2. Signal reflection: The light reflects from the surface and returns to the sensor.
  3. Time measurement: The internal electronics measure the time taken for the light to travel to the surface and back.
  4. Distance calculation: The sensor calculates the distance from the sensor to the liquid surface.
  5. Level calculation: Using the configured tank dimensions and reference point, the sensor converts the measured distance into a level value.
  6. Signal transmission: The sensor provides a 4–20 mA output for a compatible PLC, DCS, indicator, or monitoring system.

For a simple tank with a fixed reference height, the liquid level is calculated as:

Liquid level = Reference height − Measured distance

The exact scaling depends on the installation and configured tank geometry.

Main Advantages

  • Non-contact measurement: The sensor does not need to touch the liquid.
  • Low-power laser technology: Provides precise distance measurement without conventional radar electronics.
  • Compact design: Its small housing supports space-constrained installations.
  • High protection rating: IP68 protection supports demanding environments when installed according to the manufacturer’s instructions.
  • Standard analogue output: The 4–20 mA signal integrates with common industrial control systems.
  • Bluetooth configuration: Simplifies setup and adjustment of supported parameters.
  • Flexible tank configuration: Supports standard tank formats and up to 20 measuring points for irregular geometries.
  • No moving measurement parts: Reduces mechanical wear associated with moving level mechanisms.

Typical Applications

The OFST-ID can be considered for:

  • Intermediate bulk containers (IBCs)
  • Liquid storage tanks and containers
  • Water-level monitoring
  • Industrial liquid-level measurement
  • Selected chemical storage applications, subject to material compatibility
  • Applications requiring non-contact measurement in compact installations

Installation and Selection Considerations

Install the sensor in a position that provides a clear optical path to the liquid surface. Avoid obstructions, fittings, and other objects that could interfere with the reflected signal.

In addition, check the tank geometry, maximum measurement distance, mounting position, and required output scaling. Surface conditions, condensation, deposits on the optical window, and the reflective properties of the target may affect measurement performance.

Although the sensor has an IP68 rating, verify the manufacturer’s mounting and immersion instructions before installation. Also, do not assume that the product is suitable for explosive atmospheres unless the exact model carries the required hazardous-area certification.

Conclusion

The Müller IE OFST-ID is a compact optical level sensor designed for non-contact level measurement using low-power laser time-of-flight technology. With a measuring range up to 4,000 mm, ±3 mm accuracy, Bluetooth configuration, and a 4–20 mA output, it offers a practical solution for compatible tank and container applications.

Note: The OFST-ID is an optical laser sensor, not a conventional radar level transmitter. Use the manufacturer’s product designation when preparing technical documentation and product listings.

About Muller IE

Products & Features

Müller Industrie Elektronik GmbH from Germany is specializing in modular and compact sensors for customized hardware and electronic solutions, IO Link, digital displays, OEM manufacturing, digital displays, product certifications, etc.

  • Sensors & Transmitters: Temperature, Force, Pressure, Level, Flow, Humidity, and Inclination measurement.
  • MI-Series (Modular Inline Sensors): High-density, miniature housing designed for, restricted spaces in machinery, plant engineering, and vehicle construction.
  • Digital Indicators
  • OEM Electronics & IO-Link: Customized, low-cost sensor boards and IO-Link-capable products for industrial automation.
  • Safety Technology: SMM-HD-SIL1-IO: Strain gauge bridge measuring amplifier with SIL1/PLc safety

Key Benefits

  • Broad Sensor Portfolio
  • Modular Product Design
  • Robust & Certified Technology: IECEx, EHEDG, SIL3, TÜV-certified
  • Advanced Digital Indicators: full graphic TFT (LCD) displays and universal measuring instruments
  • In-house Development & Production: made in Germany